Monday - Sunday : 24 Hour Service

Call an Expert: +1 877 377 4737

Troubleshooting and Cleaning a Drain

TROUBLESHOOTING YOUR DRAIN PROBLEM


If you have on old house, and you're having problems with water pressure, it may be more than a faulty faucet or shower head. But it doesn't hurt to rule out the simple things before moving onto more complex ones! First, ask yourself if the water pressure is general to the whole house or only in one or two spots. If it's everywhere, you have a global problem, but if it's only happening in the bathroom or the kitchen, you may have a simpler problem to solve. If it's in the shower or tub, it may be a problem at the site of delivery instead of in the walls: make sure that the faucet isn't clogged.

SIDE NOTE


IF THE PROBLEM IS A FAUCET OR SHOWER HEAD


Take the fixture apart and inspect it: is the hole in the pipe open, or has it filled up with mineral deposits? You'd be amazed at the things that can end up in your water lines. Especially in cities with large water mains, sediment can actually produce little pebbles that make their way through the water lines and get trapped in a faucet or shower.


Make sure shower heads aren't clogged with debris: if they are, you can clean them yourself. Sometimes all you have to do it take off the fixture and knock the rocks out: otherwise, you might have to soak it in vinegar overnight and give it a good scrubbing before replacing it. If it is the shower, you're in luck: you can spend a little time and clean out the clogged head or just replace the whole shower head for about $15.


WHEN THE PROBLEM IS YOUR DRAIN OR PIPES


Once you've ruled out any problems with fittings and fixtures, you may discover that the problem is with the actual pipes in your house. Nothing in a house can last forever—roofs need to be re-shingled, wooden boards go rotten when damp, and sills sometimes need to be replaced.


Old water pipes are no exception, they also outlive their usefulness when they get clogged with mineral deposits, which is inevitable over time. Because old pipes were usually made of galvanized iron, they tend to corrode as well as to build up on the inside with minerals. Hot water makes the mineral deposits grow faster, and water lines laid horizontally also tend to build up faster than those running vertically. Old water pipes can become very clogged with minerals, and you can't clean them out because while minerals build up, the walls of the pipes are also breaking down: even removing a length of pipe with a wrench can break it like a brittle twig.


WHERE TO GO FROM HERE


It may be that once you've figured out what's involved in replacing your pipes, you don't want anything to do with it! So you hire a reputable plumber from Dr. Pipes (and get a written estimate and contract with warranties).


Some plumbers will put in copper pipes and join them to galvanized pipes which aren't as clogged. There are copper adaptors that can join the two metals, but you will end up with bigger problems than before, because the reaction between the galvanized iron and the copper creates additional corrosion in the galvanized pipe. When the copper pipes are added to the old iron ones, you will get leaks as the older pipes break down even faster than before. It's smarter in the long run to have all the piping replaced at one time if you can possibly afford it. Some people decide to go ahead and do the work themselves, so they can save the money on the plumber and can afford to do the whole job.


Take note


It can be a matter of life and death to get the right pipes when you're working in the house. Some people have made the mistake of thinking their natural gas lines are water lines. Cutting into a gas line will cause an explosion! Gas lines are often black, and galvanized iron water pipes are gray unless someone has painted them. If they’re painted, you may have problems figuring out which pipes go with which utility. Water pipes are usually 7/8ths on an inch in diameter, but lines may vary depending on the date on construction, building codes and builders who built it. The upshot is that you should never work on a pipe unless you are absolutely sure you know what's inside it!


If you buy fittings that don't come with the solder already on them, make sure you buy lead free solder: you don't want lead ending up in your water! To solder copper pipes, you'll need the tubing, a tube cutter of, flux, and a propane torch. If you're new to soldering or haven't done it in a while, practice on some leftover tubing first, so you're confident when it comes time to solder the actual joints.


CONSIDER CALLING A PRO


If you've found that a clog in your pipe is the problem, or if you aren't sure about exactly where it is located, or what options you have when for repair and replacement materials, don't hesitate to call us at 1-877-DRPIPES (1-877-377-4737). An experienced local plumber will have a wealth of knowledge about which materials and products best suit your home plumbing system.

Call us toll-free at
+1 877 377 4737